AudioCodes MEDIAPACK VERSION 6.2 Manuel d'utilisateur Page 177
- Page / 294
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MediaPack SIP User’s Manual 8. Telephony Capabilities
Version 4.6 177 June 2005
8.3.4 Supporting V.34 Faxes
V.34 faxes don’t comply with the T.38 relay standard. We therefore provide the optional modes
described under Sections
8.3.4.1 and 8.3.4.2:
Note that the CNG detector is disabled (CNGDetectorMode=0) in all the following examples.
8.3.4.1 Using Bypass Mechanism for V.34 Fax Transmission
In this proprietary scenario, the media gateway uses a high bit-rate coder to transmit V.34 faxes,
enabling the full utilization of its speed.
Refer to the following configurations:
FaxTransportMode = 2 (Bypass)
V34ModemTransportType = 2 (Modem bypass)
V32ModemTransportType = 2
V23ModemTransportType = 2
V22ModemTransportType = 2
In this configuration, both T.30 and V.34 faxes work in Bypass mode.
Or
FaxTransportMode = 1 (Relay)
V34ModemTransportType = 2 (Modem bypass)
V32ModemTransportType = 2
V23ModemTransportType = 2
V22ModemTransportType = 2
In this configuration, T.30 fax uses T.38 Relay mode while V.34 fax uses Bypass mode.
8.3.4.2 Using Relay mode for both T.30 and V.34 faxes
In this scenario, V.34 fax machines are compelled to use their backward compatibility with T.30
faxes; as a T.30 machine, the V.34 fax can use T.38 Relay mode.
Refer to the following configuration:
FaxTransportMode = 1 (Relay)
V34ModemTransportType = 0 (Transparent)
V32ModemTransportType = 0
V23ModemTransportType = 0
V22ModemTransportType = 0
Both T.30 and V.34 faxes use T.38 Relay mode. This configuration forces the V.34 fax machine
to operate in the slower T.30 mode.
8.4 Call Termination on MediaPack/FXO
The following six methods for call termination are supported by the MediaPack/FXO. Note that
the used disconnection methods must be supported by the CO or PBX.
• Detection of polarity reversal / current disconnect -
This is the recommended method. The call is immediately disconnected after polarity
reversal or current disconnect is detected on the Tel side (assuming the PBX / CO produces
this signal).
Relevant parameters: EnableReversalPolarity, EnableCurrentDisconnect,
CurrentDisconnectDuration, CurrentDisconnectDefaultThreshold and
TimeToSampleAnalogLineVoltage.
- MediaPack SIP User’s Manual 1
- Table of Contents 3
- List of Figures 9
- MediaPack SIP 10
- List of Tables 12
- Trademarks 15
- Customer Support 15
- Related Documentation 15
- 1 Overview 17
- 1.3 SIP Overview 18
- 1.4 MediaPack Features 19
- 1.4.4 SIP Features 20
- 2.1.1 MP-1xx Front Panel 23
- 2.1.2 MP-1xx Rear Panel 25
- 2.2.1 MP-11x Front Panel 27
- 2.2.2 MP-11x Rear Panel 28
- 3 Installing the MediaPack 29
- 3.1.2 Mounting the MP-1xx 30
- of the 31
- 3.1.3 Cabling the MP-1xx 33
- MP-124 Safety Notice 33
- DB-9 female for PC 35
- DB-9 male for MP-1xx 35
- Version 4.6 37 June 2005 37
- 3.2 Installing the MP-11x 38
- 3.2.4 Mounting the MP-11x 39
- 3.2.5 Cabling the MP-11x 41
- 4 Getting Started 43
- B.11.1 on page 263 45
- 4-1: Quick Setup Screen 45
- 5 Configuring the MediaPack 47
- 10.5 on 49
- 5.4.1 Main Menu Bar 50
- 5.4.2 Saving Changes 50
- 5.5 Protocol Management 51
- Version 4.6 53 June 2005 53
- Version 4.6 55 June 2005 55
- Version 4.6 57 June 2005 57
- 5.5.4.2 on page 83) 57
- Version 4.6 59 June 2005 59
- Version 4.6 69 June 2005 69
- 5.5.8.4 on page 104) 74
- 5.5.8.3 on page 103) 74
- 5.5.8.2 on page 102) 74
- 5.5.8.3 on page 103 76
- Version 4.6 85 June 2005 85
- 5.5.6 on page 97 86
- 5.5.7 on page 86
- 5-12) 87
- 5.5.5.2 Tel Profile Settings 93
- 5.5.5.3 IP Profile Settings 95
- 5-26: FXO Settings Screen 107
- 5.9 on page 107
- 5-27: Voice Mail Screen 109
- 5.6 Advanced Configuration 114
- 9.6 on page 125
- Version 4.6 129 June 2005 129
- Version 4.6 131 June 2005 131
- 7.3.2 on page 167 131
- 5.6.2.1 below) 134
- 5.6.2.2 on page 136) 134
- 5.6.2.3 on page 139) 134
- 5.6.2.4 on page 141) 134
- Version 4.6 135 June 2005 135
- Parameter Description 135
- Version 4.6 137 June 2005 137
- 5.6.4 Regional Settings 145
- 5.7.1 Gateway Statistics 147
- 5-44 shows the 148
- 5.7.4 Device Information 154
- 5.8.1 below) 155
- 5.8.2 on page 159) 155
- 5.8.2 Auxiliary Files 159
- 5.9 Save Configuration 161
- 5.10 Resetting the MediaPack 162
- 6.1 Secured ini File 163
- 6.2 Modifying an ini File 163
- 6.3 The ini File Structure 164
- 7 Using BootP / DHCP 165
- 14 on page 223) 166
- 8 Telephony Capabilities 169
- 8.1.3 Call Transfer 170
- 8.1.4 Call Forward 170
- 5-27) 171
- 8.3.1 Fax/Modem Settings 176
- 8.3.4 Supporting V.34 Faxes 177
- D.1.3 on page 274) to 178
- 5.5.4.2 179
- 8.7.3 Relevant Parameters 180
- 8.9 Call Detail Report 181
- 8.11 Configuration Examples 183
- 8.11.2 SIP Call Flow 184
- (Phone connected to FXS) 189
- Dialing Mode’ to ‘Two Stage’ 191
- IsTwoStageDial=1) 191
- 9 Networking Capabilities 193
- 9.6 VLANS and Multiple IPs 196
- 5.6.1.8 on page 125 197
- 9.6.2.1 Operation 197
- 10-3) 202
- 10.4 Startup Process 204
- Version 4.6 205 June 2005 205
- 10.5.4 on 208
- 6.2 on page 208
- 10.5.4 on page 210 209
- 11 Special Applications 211
- 12 Security (MP-11x Only) 213
- 12.1.3 Secured Telnet 214
- 5.9 on page 161) and 215
- 12.1.5 Client Certificates 216
- 6.2 on page 163 218
- 12.2 on page 217) 219
- 5.6.1.4 on 220
- 15.7.1 on page 233) 220
- 13 Diagnostics 221
- 13.2 Syslog Support 222
- 14.1 Accessing the CLI 223
- 14.2 Using the CLI 224
- 15 SNMP-Based Management 227
- 15.1.2 SNMP MIB Objects 228
- 15.3 Cold Start Trap 229
- Measurements 230
- 15.5 Supported MIBs 231
- 15.6 Traps 232
- 15.7 SNMP Interface Details 233
- 15.7.2 Trusted Managers 235
- 5.6.1.3 on page 119 236
- 15.7.1.1 below 236
- 15.7.1.2 on page 233 236
- 16 Configuration Files 241
- Version 4.6 245 June 2005 245
- 16.2.1 PRT File Format 246
- 5.8.2.1 on page 160) 247
- 17.1 MP-1xx Specifications 249
- 17.2 MP-11x Specifications 251
- B.2 An Overview of BootP 257
- B.3 Key Features 257
- B.5 Installation 258
- B.4 Specifications 258
- Log Window 259
- B.9 Log Window 260
- B.10.1 BootP Preferences 261
- B.10.2 TFTP Preferences 262
- B.11.1 Adding Clients 263
- B.11.2 Deleting Clients 264
- B.11.4 Testing the Client 264
- B.11.6 on page 266 265
- Allocation 269
- D.1 below) 271
- D.1.3 on page 274) 271
- D.1.1 on page 272) 271
- D.1.2 on page 273) 271
- 6.1 on page 163 273
- D.2.2 Installation 276
- D.2.3 Initial Settings 276
- Appendix E SNMP Traps 281
- E.1.5 Other Traps 285
- E.1.6 Trap Varbinds 285
- F.1 MP-1xx FXS 287
- F.2 MP-1xx FXO 288
- Safety Notice 289
- Industry Canada Notice 289
- Network Compatibility 289
- Telecommunication Safety 289
- F.3 MP-124 290
- FCC Statement 291
- F.4 MP-11x FXS 292
- Original 293
- CD or Web site 293
Produits connexes et manuels pour Mise en réseau AudioCodes MEDIAPACK VERSION 6.2
(81 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels