AudioCodes MEDIAPACK VERSION 6.2 Manuel d'utilisateur Page 174
- Page / 294
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
MediaPack SIP
MediaPack SIP User’s Manual 174 Document #: LTRT-65405
5. Sending DTMF digits (in RTP packets) as part of the audio stream (DTMF Relay is disabled):
Note that this method is normally used with G.711 coders; with other LBR coders the quality
of the DTMF digits is reduced.
To ser this mode:
¾ ‘IsDTMFUsed’ = 0 (Use Out-of-Band DTMF = No)
¾ ‘TxDTMFOption’ = 0 (DTMF RFC 2833 Negotiation = Disable)
¾ ‘RxDTMFOption = 0’ (Declare RFC 2833 in SDP = Yes)
¾ ‘DTMFTransportType = 2’ (DTMF Transport Type = Transparent DTMF)
Note 1: The gateway is always ready to receive DTMF packets over IP, in all
possible transport modes: INFO messages, NOTIFY and RFC 2833 (in
proper payload type) or as part of the audio stream.
Note 2: To exclude RFC 2833 Telephony event parameter from the gateway’s SDP,
set ‘RxDTMFOption = 0’ in the ini file.
The following parameters affect the way the MediaPack SIP handles the DTMF digits:
Table
8-1: Summary of DTMF configuration Parameters (continues on pages 174 to 175)
ini File Field Name
[Web Name]
Valid Range and Description
IsDTMFUsed
[Use Out-of-Band DTMF]
Use out-of-band signaling to relay DTMF digits.
No [0] = DTMF digits are sent inband (default).
Yes [1] = DTMF digits are sent out-of-band according to the parameter ‘Out-of-band
DTMF format’.
Note: When out-of-band DTMF transfer is used, the parameter ‘DTMF Transport Type’ is
automatically set to 0 (erase the DTMF digits from the RTP stream).
OutOfBandDTMFFormat
[Out-of-Band DTMF Format]
The exact method to send out-of-band DTMF digits.
INFO (Nortel) [1] = Sends DTMF digits according with IETF <draft-choudhuri-sip-
info-digit-00>.
INFO (Cisco) [2] = Sends DTMF digits according with Cisco format (default).
NOTIFY (3Com) [3] = NOTIFY format <draft-mahy-sipping-signaled-digits-01.txt>.
Note 1: To use out-of-band DTMF, set ‘IsDTMFUsed=1’.
Note 2: When using out-of-band DTMF, the ‘DTMFTransportType’ parameter is
automatically set to 0, to erase the DTMF digits from the RTP stream.
TxDTMFOption
[DTMF RFC 2833
Negotiation]
Disable [0] = No negotiation, DTMF digit is sent according to the parameters ‘DTMF
Transport Type’ and ‘RFC2833PayloadType’ (default).
Enable [4] = Enable RFC 2833 payload type (PT) negotiation
Note 1: This parameter is applicable only if ‘IsDTMFUsed=0’ (out-of-band DTMF is not
used).
Note 2: If enabled, the gateway:
• Negotiates RFC 2833 payload type using local and remote SDPs.
• Sends DTMF packets using RFC 2833 PT according to the PT in the received SDP.
• Expects to receive RFC 2833 packets with the same PT as configured by the
‘RFC2833PayloadType’ parameter.
Note 3: If the remote party doesn’t include the RFC 2833 DTMF relay payload type in the
SDP, the gateway uses the same PT for send and for receive.
Note 4: If TxDTMFOption is set to 0, the RFC 2833 payload type is set according to the
parameter ‘RFC2833PayloadType’ for both transmit and receive.
- MediaPack SIP User’s Manual 1
- Table of Contents 3
- List of Figures 9
- MediaPack SIP 10
- List of Tables 12
- Trademarks 15
- Customer Support 15
- Related Documentation 15
- 1 Overview 17
- 1.3 SIP Overview 18
- 1.4 MediaPack Features 19
- 1.4.4 SIP Features 20
- 2.1.1 MP-1xx Front Panel 23
- 2.1.2 MP-1xx Rear Panel 25
- 2.2.1 MP-11x Front Panel 27
- 2.2.2 MP-11x Rear Panel 28
- 3 Installing the MediaPack 29
- 3.1.2 Mounting the MP-1xx 30
- of the 31
- 3.1.3 Cabling the MP-1xx 33
- MP-124 Safety Notice 33
- DB-9 female for PC 35
- DB-9 male for MP-1xx 35
- Version 4.6 37 June 2005 37
- 3.2 Installing the MP-11x 38
- 3.2.4 Mounting the MP-11x 39
- 3.2.5 Cabling the MP-11x 41
- 4 Getting Started 43
- B.11.1 on page 263 45
- 4-1: Quick Setup Screen 45
- 5 Configuring the MediaPack 47
- 10.5 on 49
- 5.4.1 Main Menu Bar 50
- 5.4.2 Saving Changes 50
- 5.5 Protocol Management 51
- Version 4.6 53 June 2005 53
- Version 4.6 55 June 2005 55
- Version 4.6 57 June 2005 57
- 5.5.4.2 on page 83) 57
- Version 4.6 59 June 2005 59
- Version 4.6 69 June 2005 69
- 5.5.8.4 on page 104) 74
- 5.5.8.3 on page 103) 74
- 5.5.8.2 on page 102) 74
- 5.5.8.3 on page 103 76
- Version 4.6 85 June 2005 85
- 5.5.6 on page 97 86
- 5.5.7 on page 86
- 5-12) 87
- 5.5.5.2 Tel Profile Settings 93
- 5.5.5.3 IP Profile Settings 95
- 5-26: FXO Settings Screen 107
- 5.9 on page 107
- 5-27: Voice Mail Screen 109
- 5.6 Advanced Configuration 114
- 9.6 on page 125
- Version 4.6 129 June 2005 129
- Version 4.6 131 June 2005 131
- 7.3.2 on page 167 131
- 5.6.2.1 below) 134
- 5.6.2.2 on page 136) 134
- 5.6.2.3 on page 139) 134
- 5.6.2.4 on page 141) 134
- Version 4.6 135 June 2005 135
- Parameter Description 135
- Version 4.6 137 June 2005 137
- 5.6.4 Regional Settings 145
- 5.7.1 Gateway Statistics 147
- 5-44 shows the 148
- 5.7.4 Device Information 154
- 5.8.1 below) 155
- 5.8.2 on page 159) 155
- 5.8.2 Auxiliary Files 159
- 5.9 Save Configuration 161
- 5.10 Resetting the MediaPack 162
- 6.1 Secured ini File 163
- 6.2 Modifying an ini File 163
- 6.3 The ini File Structure 164
- 7 Using BootP / DHCP 165
- 14 on page 223) 166
- 8 Telephony Capabilities 169
- 8.1.3 Call Transfer 170
- 8.1.4 Call Forward 170
- 5-27) 171
- 8.3.1 Fax/Modem Settings 176
- 8.3.4 Supporting V.34 Faxes 177
- D.1.3 on page 274) to 178
- 5.5.4.2 179
- 8.7.3 Relevant Parameters 180
- 8.9 Call Detail Report 181
- 8.11 Configuration Examples 183
- 8.11.2 SIP Call Flow 184
- (Phone connected to FXS) 189
- Dialing Mode’ to ‘Two Stage’ 191
- IsTwoStageDial=1) 191
- 9 Networking Capabilities 193
- 9.6 VLANS and Multiple IPs 196
- 5.6.1.8 on page 125 197
- 9.6.2.1 Operation 197
- 10-3) 202
- 10.4 Startup Process 204
- Version 4.6 205 June 2005 205
- 10.5.4 on 208
- 6.2 on page 208
- 10.5.4 on page 210 209
- 11 Special Applications 211
- 12 Security (MP-11x Only) 213
- 12.1.3 Secured Telnet 214
- 5.9 on page 161) and 215
- 12.1.5 Client Certificates 216
- 6.2 on page 163 218
- 12.2 on page 217) 219
- 5.6.1.4 on 220
- 15.7.1 on page 233) 220
- 13 Diagnostics 221
- 13.2 Syslog Support 222
- 14.1 Accessing the CLI 223
- 14.2 Using the CLI 224
- 15 SNMP-Based Management 227
- 15.1.2 SNMP MIB Objects 228
- 15.3 Cold Start Trap 229
- Measurements 230
- 15.5 Supported MIBs 231
- 15.6 Traps 232
- 15.7 SNMP Interface Details 233
- 15.7.2 Trusted Managers 235
- 5.6.1.3 on page 119 236
- 15.7.1.1 below 236
- 15.7.1.2 on page 233 236
- 16 Configuration Files 241
- Version 4.6 245 June 2005 245
- 16.2.1 PRT File Format 246
- 5.8.2.1 on page 160) 247
- 17.1 MP-1xx Specifications 249
- 17.2 MP-11x Specifications 251
- B.2 An Overview of BootP 257
- B.3 Key Features 257
- B.5 Installation 258
- B.4 Specifications 258
- Log Window 259
- B.9 Log Window 260
- B.10.1 BootP Preferences 261
- B.10.2 TFTP Preferences 262
- B.11.1 Adding Clients 263
- B.11.2 Deleting Clients 264
- B.11.4 Testing the Client 264
- B.11.6 on page 266 265
- Allocation 269
- D.1 below) 271
- D.1.3 on page 274) 271
- D.1.1 on page 272) 271
- D.1.2 on page 273) 271
- 6.1 on page 163 273
- D.2.2 Installation 276
- D.2.3 Initial Settings 276
- Appendix E SNMP Traps 281
- E.1.5 Other Traps 285
- E.1.6 Trap Varbinds 285
- F.1 MP-1xx FXS 287
- F.2 MP-1xx FXO 288
- Safety Notice 289
- Industry Canada Notice 289
- Network Compatibility 289
- Telecommunication Safety 289
- F.3 MP-124 290
- FCC Statement 291
- F.4 MP-11x FXS 292
- Original 293
- CD or Web site 293
Produits connexes et manuels pour Mise en réseau AudioCodes MEDIAPACK VERSION 6.2
(81 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.041 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels