AudioCodes Mediant Series Spécifications Page 94
- Page / 136
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Spectralink 84-Series with AudioCodes Gateway and Avaya Communication Manager: Interoperability Guide
1725-86914-000_C.docx
September 2013 94
1. Add another DS1
1 Enter add ds1 xxxxx command, where xxxxx is the carrier/slot location of the DS1
connected to the Mediant 1000. For this configuration 001v3 was used. On page 1 of the
ds1 form configure the following:
Name
Enter something meaningful
Bit Rate
1.544
Line Coding
b8zs
Frame mode
esf
Signaling Mode
isdn-pri
Connect
PBX
Interface
peer-master
Peer Protocol
Q-SIG
Side
a
2 Press Esc-E to submit.
2. Add Signaling Group
1 Enter the command add signaling-group x, where x is the number of the signaling group
you wish to add.
- AudioCodes Gateway and 1
- Avaya Communication Manager 1
- Copyright Notice 2
- Warranty 2
- Contact Information 2
- Contents 3
- September 2013 4 4
- September 2013 5 5
- September 2013 6 6
- Introduction 7
- Product Support 8
- Spectralink References 8
- AudioCodes References 9
- Typography 12
- September 2013 13 13
- Chapter 1: Test Overview 14
- Network Topology 15
- 16
- Why Q.SIG? 17
- A Word about Wi-Fi 17
- September 2013 18 18
- September 2013 19 19
- SAS Emergency State 20
- User Authentication 20
- System Capacity Requirements 21
- Capacity Analysis 21
- September 2013 22 22
- September 2013 23 23
- Footnotes 24
- September 2013 25 25
- Package Contents 26
- T1/E1 Module 27
- CRMX Module 28
- Rear-Panel Description 29
- Insert the T1/E1 Module 30
- Connect to Power 31
- Connect to Computer 31
- Part II: Configuring the 32
- Components 32
- Mediant Gateway 33
- The Home screen 34
- The Burn button 34
- Navigation Pane 34
- The Search option 35
- Device Actions 35
- Verify License keys feature 35
- September 2013 36 36
- September 2013 37 37
- Disable the DHCP Client 38
- Set DHCP Lease Renewal 39
- September 2013 40 40
- Verify the settings 41
- September 2013 42 42
- 5. Set NTP settings 43
- 6. Set Syslog Parameters 44
- Set CDR Reporting 45
- September 2013 46 46
- 7. Enable SAS Application 47
- Configure SAS 48
- September 2013 49 49
- September 2013 50 50
- September 2013 51 51
- September 2013 52 52
- September 2013 53 53
- 4 Click Submit 54
- September 2013 55 55
- September 2013 56 56
- Avoiding a Routing Loop 57
- Detecting a routing loop 58
- September 2013 59 59
- 14. Enable Early Media 60
- 15. TDM configuration 61
- 16. B-Channel negotiation 62
- 17. Setting up the PRI 63
- September 2013 64 64
- September 2013 65 65
- Q931 Layer Response Behavior 66
- Set Call Rerouting 66
- September 2013 67 67
- 18. Changing the Password 68
- Gateway 69
- 19-inch Rack Mounting 70
- Cabling the Mediant 1000 72
- Connecting to E1/T1 Trunks 73
- Connecting to Power 74
- September 2013 75 75
- 1. Q.SIG 76
- September 2013 77 77
- September 2013 78 78
- September 2013 79 79
- September 2013 80 80
- 3 Press Esc-E to submit 81
- September 2013 82 82
- 4. Add a Trunk Group 83
- September 2013 84 84
- September 2013 85 85
- September 2013 86 86
- September 2013 87 87
- September 2013 88 88
- 5. Change Signaling Group 89
- 6. Set up Dialing Parameters 90
- 2 Add these parameters: 91
- 8. Add the Route Pattern 92
- 1. Add another DS1 94
- September 2013 95 95
- 3. Add a Trunk Group 96
- September 2013 97 97
- September 2013 98 98
- September 2013 99 99
- 1725-86914-000_C.docx 100
- September 2013 100 100
- 4. Change Signaling Group 101
- 5. Set up Dialing Parameters 102
- September 2013 103 103
- 7. Add the Route Pattern 104
- 8. Set Caller ID 104
- September 2013 105 105
- September 2013 106 106
- 1. Add the DS1 107
- 2. Add Signaling Group 107
- September 2013 108 108
- 3. Add Channels 109
- September 2013 110 110
- September 2013 111 111
- September 2013 112 112
- September 2013 113 113
- September 2013 114 114
- Troubleshooting 115
- PBX Functionality 116
- Chapter 12: Troubleshooting 117
- Caller ID 118
- Program a 10-digit Caller ID 118
- Clearing the configuration 119
- Manual method 119
- Software method 119
- September 2013 120 120
- Part IV: Appendices 121
- September 2013 122 122
- September 2013 123 123
- The software will load: 124
- The screen will display: 125
- September 2013 126 126
- Appendix C: Sample Files 127
- September 2013 128 128
- September 2013 129 129
- September 2013 130 130
- September 2013 131 131
- September 2013 132 132
- September 2013 133 133
- September 2013 134 134
- September 2013 135 135
- September 2013 136 136
Produits connexes et manuels pour Passerelles/contrôleurs AudioCodes Mediant Series
(63 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels