AudioCodes MP-11 Manuel d'utilisateur

1 MMiiccrroossoofftt EExxcchhaannggee SSeerrvveerr 22000077 UUnniiffiieedd MMeessssaaggiinngg PPBBXX CCoonnffiigguurraattiioonn NNoott

10 Step 6: Disconnect Supervision Setup

11 Step 7: Message Waiting Indication Setup

12 Step 8: Manipulation Routing Setup

13 Step 9: Endpoints Setup Note: The phone numbers must correspond to your network environment as the dial plan pilot number is configured for this

14 Step 10: Voicemail In-Band DTMF Setup

15 Step 11: FAX Setup

16 Step 12: FXO General Setup Step 13: FXO General Setup (Cont.) • CurrentDisconnectDuration = 450 • EchoCancellerAggressiveNLP = 1 • EnableDe

17 Step 14: Reset FXO Note: Steps 1 and 7 involve core configuration changes (versus default settings): • Proxy IP Address (Microsoft Unified Mes

18 Step 15: Save Gateway Configuration Note: This step is optional and is note required if you performed Step 14.

19 4.1. Configuration Files • AudioCodes configuration ini file (.ini file extension). INI Avaya S8300.zip

2 Content This document describes the configuration required to setup Avaya S8300 and AudioCodes MP-11x FXO using analog lines with inband DTMF as th

20 4.2. TLS Setup Step 1: PBX to IP Routing Setup Note: The Proxy IP Address and Name must be one that corresponds to the network environment in w

21 Step 2: SIP Environment and Gateway Name Setup Note: Assign an FQDN name to the gateway (for example, gw2.fxoaudiocodes.com). Any gateway name t

22 Step 3: SIP Environment Setup (Cont.)

23 Step 4: DNS Servers Setup Note: Define the primary and secondary DNS servers' IP addresses so that they correspond to your network environm

24 Step 5: Internal DNS Setup Note: If no DNS server is available in the network, define the internal DNS table where the domain name is the FQDN o

25 Step 6: NTP Server Setup Note: Define the NTP server’s IP address so that it corresponds to your network environment (for example, 10.15.3.50).

26 Step 7: Generate Certificate Setup Use the screen below to generate CSR. Copy the certificate signing request and send it to your Certification Au

27 Step 8: Uploading Certificates Setup The screen below is used to upload the sign certificates. In the “Server Certificate” area, upload the gatew

28 5. PBX Setup Notes Information used for this test case: • Analog VoiceMail ports: ext. 5098 and 5099 • VoiceMail Hunt Group Pilot: ext. 5095 •

29 Step 1: Define analog voice mail ports: “add station” or “cha station” command: Page 1: Set port type as VMI

3 1. Components Information 1.1. PBX or IP-PBX PBX Vendor Avaya Model S8300 Software Version G3xV11 Communication Manager 1.3 Telephony Signalin

30 Page 2: Set adjunct supervision to Y Repeat this process for all analog VoiceMail ports.

31 Step 2: Define a hunt group for analog VoiceMail ports: “add hunt-group” or “cha hunt-group” command Page 1: Set group type as UCD-MIA

32 Add analog voice mail ports to this hunt group. Page 3.

33 Step 3: Set the coverage path “add coverage-path” or “cha coverage-path” commands Point to the analog voice mail hunt group 5095 H1 in point1

34 Step 4: Add or change station coverage path: Define user station (analog or digital) with coverage path: Use “add station” or ”change station” com

35 Step 5: Display mode-code information. It shows DTMF codes sent by the PBX associated with different types of calls. Use “display system-paramete

36 Step 6: Verify and change if needed MWI on & off codes. Use “display feature-access-codes” command Leave Word Calling Send A Message: *2 (MWI

37 5.1. TLS Setup • N/A. 5.2. Fail-Over Configuration • N/A. 5.3. Tested Phones Avaya 2420 Digital phone. 5.4. Other Comments None.

38 6. Exchange 2007 UM Validation Test Matrix The following table contains a set of tests for assessing the functionality of the UM core feature set

39 Dial the extension for the AA and confirm the AA answers the call. 6 Call Transfer by Directory Search. 6a Call Transfer by Directory Searc

4 2. Prerequisites 2.1. Gateway Prerequisites • Current Disconnect must be configured in the gateway and the duration must be adjusted for better

40 Confirm the FAX is received in the user’s inbox. 10 Setup TLS between gateway/IP-PBX and Exchange UM. Windows Certificate Authority (CA). 10

41 6.1. Detailed Description of Limitations Failure Point None Phone type (if phone-specific) Call scenarios(s) associated with failure point L

42 7. Troubleshooting The tools used for debugging include network sniffer applications (such as Ethereal) and AudioCodes' Syslog protocol. The

43 3. To determine the Syslog logging level, use the parameter Debug Level and set this parameter to '5'. 4. Change the CDR Report Level

44 Appendix 1. Dial Pilot Number and Mailbox Login • Dial the pilot number of the UM server from an extension that is NOT enabled for UM. • Confir

45 b. From an External Phone a. From an external phone, dial the extension for a UM-enabled user and leave a voicemail message. b. Confirm the voi

46 • Note: Even though some keys are associated with three or four numbers, for each letter, each key only needs to be pressed once regardless of th

47 • Once it is received in the user’s inbox, use OWA’s Play-On-Phone to dial an internal extension. • Confirm the voicemail is delivered to the co

48 9. FAX • Use the Management Console or the Management Shell to FAX-enable a user. • Management Console: a. Double click on a user’s mailbox an

49 12. Message Waiting Indicator (MWI) • Although Exchange 2007 UM does not natively support MWI, Geomant has created a 3rd party solution - MWI2007

5 4. Gateway Setup Notes Step 1: SIP Environment Setup

6 Step 2: Routing Setup Note: The Proxy IP Address must be one that corresponds to the network environment in which the Microsoft Unified Messaging

7 Step 3: SIP Environment Setup (Cont.)

8 Step 4: Coder Setup

9 Step 5: Digit Collection Setup